Valiol Trading supplies certified structural steel sections and plates from Qatar-held stock — I-beams (IPE/HEA/HEB), hollow sections (SHS/RHS/CHS), equal angles, channels, flat bars, and steel plates in S275/S355, ASTM A36/A572, high-strength, and abrasion-resistant grades — cut-to-length with same-week delivery to Doha, Ras Laffan, and all Qatar construction and EPC project sites.
Valiol Trading is a certified structural steel supplier headquartered in Doha, Qatar. We supply the complete range of structural steel sections and plates — I-beams, H-sections, hollow sections, angles, channels, flat bars, and plates — to Qatar's oil & gas EPC contractors, construction companies, infrastructure projects, and steel fabricators.
Our Qatar-held stock covers the most commonly specified grades (S275/S355 and ASTM A36/A572) in standard section sizes and plate thicknesses — available for same-week delivery across Doha, Ras Laffan, Mesaieed, and all Qatar project sites. Cut-to-length, plate profiling, and shot blasting services are available through our Qatar processing partners.
Every structural steel section, plate, and bar required for Qatar construction, oil & gas, and industrial projects — from standard mild steel to high-strength and specialty grades, all from Qatar-stocked inventory.
Hot-rolled I-sections and wide-flange H-sections for Qatar primary beams, floor beams, portal frames, and column supports. European IPE (standard I-beam), HEA (wide flange light), and HEB (wide flange heavy) sections stocked in S275/S355 JR/J0/J2.
Heavy H-sections with wide parallel flanges optimised for axial load in Qatar multi-storey steel frames, transfer structures, and heavy industrial steelwork. European HEM and British UC sections. ASTM A992 W-sections for US-specification Qatar EPC projects.
Square (SHS), rectangular (RHS), and circular (CHS) hollow sections — hot-formed (EN 10210) and cold-formed (EN 10219) in S275J2H and S355J2H. High torsional stiffness for Qatar trusses, columns, pipe supports, and architectural steelwork.
Hot-rolled L-sections in equal (both legs equal) and unequal configurations. Used for Qatar bracing, trusses, connections, secondary frames, and pipe rack steelwork. EN 10056 and ASTM A36 grades. Equal angles from 25×25mm to 200×200mm.
Hot-rolled C-channels and parallel-flange channels for Qatar EPC pipe racks, crane rails, purlins, and secondary structural framing. European UPN/UPE and British PFC in S275/S355. Available in standard lengths or cut-to-length for Qatar fabrication.
Hot-rolled flat steel bar in widths 10mm–600mm and thicknesses 3mm–100mm for Qatar EPC gusset plates, base plates, stiffeners, and steel fabrication. Bulb flats for Qatar offshore stiffener and shipbuilding applications. Cut-to-length from Doha stock.
Hot-rolled (HR) and cold-rolled (CR) steel plates in mild steel (S275/S355), high-strength (S460/S690), pressure vessel quality (P355NL), abrasion-resistant (AR400/500/600), and Corten weathering steel. Standard sizes 1000×2000mm to 3000×12000mm, 3mm to 200mm thick. Cut-to-size and flame/plasma profiling available for Qatar fabrication shops.
Hot-rolled round bars (6mm–300mm), square bars (8mm–200mm), and hexagonal bars (AF 8mm–100mm) in mild steel and medium carbon steel. Used for Qatar equipment shafts, fastener blanks, machined components, and general steel fabrication. EN 10060/10058 and ASTM A36/A108.
Universal Beam
IPE / HEA / HEB
Rectangular / Square
Hollow Section
Circular
Hollow Section
Equal & Unequal
L-section
UPN / PFC
C-section
Flat bar, plate
Rectangular section
Detailed section sizes, weights, dimensions, and section properties for all structural steel products. All available with EN 10204 3.1 MTC and same-week Qatar delivery. Contact our Doha team for pricing, stock availability, and cut-to-length options.
Hot-rolled European I and H sections to EN 10025-2 in S275 / S355 JR, J0, J2. IPE = standard I-beam; HEA = wide flange light series; HEB = wide flange heavy series. Standard stock length 12m or 6m. Cut-to-length available from Qatar stock.
| Section | Designation | Height h (mm) | Flange Width b (mm) | Web Thick. tw (mm) | Flange Thick. tf (mm) | Mass (kg/m) | Ix (cm⁴) | Wx (cm³) |
|---|---|---|---|---|---|---|---|---|
| IPE SERIES — PARALLEL FLANGE I-BEAMS (EN 10025 S275 / S355) | ||||||||
| IPE 100 | IPE | 100 | 55 | 4.1 | 5.7 | 8.1 | 171 | 34.2 |
| IPE 160 | IPE | 160 | 82 | 5.0 | 7.4 | 15.8 | 869 | 123 |
| IPE 200 | IPE | 200 | 100 | 5.6 | 8.5 | 22.4 | 1,943 | 194 |
| IPE 240 | IPE | 240 | 120 | 6.2 | 9.8 | 30.7 | 3,892 | 324 |
| IPE 300 | IPE | 300 | 150 | 7.1 | 10.7 | 42.2 | 8,356 | 557 |
| IPE 360 | IPE | 360 | 170 | 8.0 | 12.7 | 57.1 | 16,270 | 904 |
| IPE 400 | IPE | 400 | 180 | 8.6 | 13.5 | 66.3 | 23,130 | 1,156 |
| IPE 450 | IPE | 450 | 190 | 9.4 | 14.6 | 77.6 | 33,740 | 1,500 |
| IPE 500 | IPE | 500 | 200 | 10.2 | 16.0 | 90.7 | 48,200 | 1,928 |
| IPE 550 | IPE | 550 | 210 | 11.1 | 17.2 | 106.0 | 67,120 | 2,440 |
| IPE 600 | IPE | 600 | 220 | 12.0 | 19.0 | 122.0 | 92,080 | 3,069 |
| HEA SERIES — WIDE FLANGE I-SECTIONS (LIGHT) | ||||||||
| HEA 100 | HEA | 96 | 100 | 5.0 | 8.0 | 16.7 | 349 | 72.8 |
| HEA 200 | HEA | 190 | 200 | 6.5 | 10.0 | 42.3 | 3,692 | 389 |
| HEA 300 | HEA | 290 | 300 | 8.5 | 14.0 | 88.3 | 18,260 | 1,260 |
| HEA 400 | HEA | 390 | 300 | 11.0 | 19.0 | 125.0 | 45,070 | 2,311 |
| HEA 500 | HEA | 490 | 300 | 12.0 | 23.0 | 155.0 | 86,970 | 3,550 |
| HEB SERIES — WIDE FLANGE I-SECTIONS (HEAVY) | ||||||||
| HEB 200 | HEB | 200 | 200 | 9.0 | 15.0 | 61.3 | 5,696 | 569.6 |
| HEB 300 | HEB | 300 | 300 | 11.0 | 19.0 | 117.0 | 25,170 | 1,678 |
| HEB 400 | HEB | 400 | 300 | 13.5 | 24.0 | 155.0 | 57,680 | 2,884 |
| HEB 500 | HEB | 500 | 300 | 14.5 | 28.0 | 187.0 | 107,200 | 4,287 |
Square (SHS), rectangular (RHS), and circular (CHS) hollow sections to EN 10210 (hot-formed) and EN 10219 (cold-formed) in S275J2H and S355J2H. Standard stock length 6m. Cut-to-length available for Qatar EPC and fabrication projects.
| Type | Size (mm) | Wall Thickness (mm) | Mass (kg/m) | Area (cm²) | Ix (cm⁴) | Wx (cm³) | Standard |
|---|---|---|---|---|---|---|---|
| SHS — SQUARE HOLLOW SECTIONS | |||||||
| SHS | 50×50 | 3.0 / 4.0 / 5.0 | 4.35 / 5.72 / 6.97 | 5.54 / 7.29 / 8.88 | 17.3 / 21.8 / 25.3 | 6.93 / 8.73 / 10.1 | EN 10219 |
| SHS | 80×80 | 3.0 / 4.0 / 5.0 / 6.3 | 7.18 / 9.63 / 11.9 / 14.8 | 9.15 / 12.3 / 15.2 / 18.9 | 76.0 / 99.0 / 119 / 143 | 19.0 / 24.8 / 29.8 / 35.8 | EN 10219 |
| SHS | 100×100 | 4.0 / 5.0 / 6.3 / 8.0 | 12.2 / 15.1 / 18.7 / 23.3 | 15.5 / 19.2 / 23.9 / 29.7 | 197 / 239 / 288 / 343 | 39.4 / 47.7 / 57.6 / 68.6 | EN 10219 |
| SHS | 120×120 | 5.0 / 6.3 / 8.0 / 10.0 | 18.3 / 22.7 / 28.4 / 34.7 | 23.2 / 29.0 / 36.1 / 44.2 | 421 / 511 / 619 / 726 | 70.2 / 85.2 / 103 / 121 | EN 10219 |
| SHS | 150×150 | 5.0 / 6.3 / 8.0 / 10.0 | 23.0 / 28.8 / 36.2 / 44.4 | 29.3 / 36.7 / 46.2 / 56.7 | 839 / 1,030 / 1,260 / 1,500 | 112 / 137 / 168 / 200 | EN 10219 |
| SHS | 200×200 | 6.3 / 8.0 / 10.0 / 12.5 | 39.0 / 49.2 / 60.7 / 74.5 | 49.7 / 62.6 / 77.2 / 94.9 | 2,520 / 3,110 / 3,750 / 4,440 | 252 / 311 / 375 / 444 | EN 10210 |
| RHS — RECTANGULAR HOLLOW SECTIONS | |||||||
| RHS | 100×50 | 3.0 / 4.0 / 5.0 | 6.71 / 8.86 / 10.9 | 8.54 / 11.3 / 13.9 | 90.5 / 116 / 138 | 18.1 / 23.1 / 27.5 | EN 10219 |
| RHS | 150×75 | 4.0 / 5.0 / 6.3 | 13.4 / 16.6 / 20.5 | 17.1 / 21.2 / 26.1 | 447 / 542 / 651 | 59.6 / 72.3 / 86.8 | EN 10219 |
| RHS | 200×100 | 5.0 / 6.3 / 8.0 / 10.0 | 22.3 / 27.7 / 34.7 / 42.7 | 28.4 / 35.3 / 44.2 / 54.2 | 1,280 / 1,560 / 1,890 / 2,230 | 128 / 156 / 189 / 223 | EN 10219 |
| RHS | 250×150 | 6.3 / 8.0 / 10.0 / 12.5 | 37.6 / 47.2 / 58.2 / 71.1 | 47.9 / 60.1 / 74.1 / 90.5 | 3,820 / 4,670 / 5,590 / 6,590 | 306 / 373 / 447 / 527 | EN 10210 |
| RHS | 300×200 | 8.0 / 10.0 / 12.5 | 60.5 / 74.9 / 91.9 | 77.0 / 95.3 / 117 | 9,480 / 11,450 / 13,580 | 632 / 763 / 905 | EN 10210 |
| CHS — CIRCULAR HOLLOW SECTIONS | |||||||
| CHS | OD 48.3mm | 2.5 / 3.2 / 4.0 | 2.82 / 3.56 / 4.37 | 3.59 / 4.53 / 5.57 | 10.9 / 13.5 / 16.1 | 4.51 / 5.59 / 6.68 | EN 10219 |
| CHS | OD 88.9mm | 3.2 / 4.0 / 5.0 / 6.3 | 6.76 / 8.38 / 10.3 / 12.8 | 8.62 / 10.7 / 13.2 / 16.3 | 62.3 / 76.0 / 91.6 / 110 | 14.0 / 17.1 / 20.6 / 24.8 | EN 10219 |
| CHS | OD 168.3mm | 5.0 / 6.3 / 8.0 / 10.0 | 20.1 / 25.2 / 31.6 / 39.0 | 25.7 / 32.1 / 40.3 / 49.7 | 614 / 757 / 930 / 1,120 | 73.0 / 89.9 / 110 / 133 | EN 10219 |
| CHS | OD 219.1mm | 6.3 / 8.0 / 10.0 / 12.5 | 33.1 / 41.6 / 51.6 / 63.7 | 42.1 / 53.0 / 65.7 / 81.1 | 1,680 / 2,080 / 2,520 / 3,010 | 153 / 190 / 230 / 275 | EN 10210 |
| CHS | OD 323.9mm | 8.0 / 10.0 / 12.5 / 16.0 | 62.3 / 77.4 / 95.9 / 121 | 79.4 / 98.6 / 122 / 154 | 6,710 / 8,220 / 10,010 / 12,350 | 414 / 508 / 618 / 762 | EN 10210 |
Hot-rolled equal angles to EN 10056-1 in S275 and S355. Also available to ASTM A36 and IS 2062 Grade B for Qatar projects with US or Indian-specification requirements. Standard stock length 6m and 12m.
| Designation | Leg A (mm) | Thickness t (mm) | Mass (kg/m) | Area (cm²) | Ixx (cm⁴) | Wxx (cm³) | Imin (cm⁴) | Standard |
|---|---|---|---|---|---|---|---|---|
| L 30×30×3 | 30 | 3 | 1.36 | 1.74 | 0.776 | 0.374 | 0.310 | EN 10056 |
| L 40×40×4 | 40 | 4 | 2.42 | 3.08 | 2.40 | 0.862 | 0.960 | EN 10056 |
| L 50×50×5 | 50 | 5 | 3.77 | 4.80 | 7.28 | 2.07 | 2.93 | EN 10056 |
| L 60×60×6 | 60 | 6 | 5.42 | 6.91 | 17.8 | 4.22 | 7.09 | EN 10056 |
| L 70×70×7 | 70 | 7 | 7.38 | 9.40 | 37.9 | 7.64 | 15.1 | EN 10056 |
| L 80×80×8 | 80 | 8 | 9.63 | 12.3 | 70.2 | 12.4 | 28.0 | EN 10056 |
| L 100×100×10 | 100 | 10 | 15.0 | 19.2 | 177 | 25.1 | 70.7 | EN 10056 |
| L 120×120×12 | 120 | 12 | 21.6 | 27.5 | 433 | 50.8 | 173 | EN 10056 |
| L 150×150×15 | 150 | 15 | 33.8 | 43.0 | 1,050 | 99.1 | 419 | EN 10056 |
| L 200×200×20 | 200 | 20 | 60.0 | 76.4 | 3,650 | 257 | 1,460 | EN 10056 |
Valiol Trading supplies hot-rolled, pressure vessel quality, high-strength, abrasion-resistant, and weathering steel plates for Qatar EPC, construction, and fabrication projects. Cut-to-size, plasma/flame profiling, and shot blasting available.
| Grade / Type | Standard | Yield Str. (MPa) | Tensile Str. (MPa) | Thickness Range | Width Range | Key Properties | Qatar Application |
|---|---|---|---|---|---|---|---|
| S275 JR / J0 / J2 | EN 10025-2 | ≥275 MPa | 430–580 MPa | 3–150mm | Up to 4,200mm | Standard mild steel, weldable | Qatar general structural fabrication, frames, base plates |
| S355 JR / J0 / J2 / K2 | EN 10025-2 | ≥355 MPa | 470–630 MPa | 3–150mm | Up to 4,200mm | Higher strength, good weldability | Qatar oil & gas modules, heavy fabrication, bridges |
| S355 NL / ML | EN 10025-3/4 | ≥355 MPa | 470–630 MPa | 8–100mm | Up to 3,500mm | Charpy impact at –40°C / –50°C | Qatar offshore structures, crane booms, LNG plant frames |
| S420 / S460 High Strength | EN 10025-3/4 | ≥420 / ≥460 MPa | 520–680 MPa | 8–100mm | Up to 3,200mm | High strength, reduced weight | Qatar lifting equipment, North Field modules, bridges |
| S690 QL Ultra High Strength | EN 10025-6 | ≥690 MPa | 770–940 MPa | 5–80mm | Up to 3,000mm | Q&T, very high yield, impact tested | Qatar mining equipment, special structures |
| ASTM A36 | ASTM A36 | ≥250 MPa | 400–550 MPa | 3–150mm | Up to 3,000mm | US standard, high weldability | Qatar US-spec EPC projects, ASME-code structural |
| ASTM A572 Gr.42/50/60/65 | ASTM A572 | 290–450 MPa | 415–550 MPa | 6–100mm | Up to 3,000mm | HSLA, good notch toughness | Qatar US-spec bridges, buildings, ASME pressure |
| P355 NL / P460 NL (Pressure Vessel) | EN 10028-3 | ≥355 / ≥460 MPa | 490–720 MPa | 8–150mm | Up to 4,000mm | PVQ normalised, impact tested –40°C/–50°C | Qatar pressure vessels, LPG tanks, offshore modules |
| AR400 / AR450 / AR500 | EN 10029 | ≥1000–1250 MPa | 1,250–1,600 MPa | 4–80mm | Up to 3,200mm | 400–500 Brinell hardness, extreme wear | Qatar mining, dredging, chutes, wear liner plates |
| Corten A / B (Weathering Steel) | EN 10025-5 / ASTM A588 | ≥345 MPa | 485–620 MPa | 3–50mm | Up to 3,000mm | Self-weathering oxide layer, no paint required | Qatar architecture, signage, outdoor structures |
| Chequered Plate — Diamond/Tear Drop | EN 10025 S275/S355 | ≥275 / ≥355 MPa | 430–630 MPa | 3–12mm base | 1000×2000 / 1250×2500mm | Anti-slip raised pattern | Qatar flooring, access platforms, ramps, step covers |
Selecting the correct grade ensures structural integrity, weldability, and compliance with your Qatar design code. This guide covers the most commonly specified grades for Qatar EPC and operator projects.
The most economical and widely available structural steel in Qatar stock. Yield strength 275 MPa. JR sub-grade is impact tested at room temperature (+20°C) — fully suitable for Qatar's climate. The default grade for secondary steelwork, pipe supports, miscellaneous frames, and general fabrication across Qatar construction and industrial projects.
355 MPa yield — 29% stronger than S275. Allows lighter sections for the same load, reducing steel tonnage and cost. J2 sub-grade impact tested at –20°C. The preferred grade for primary structural steel in Qatar oil & gas modules, EPC project structural steelwork, pipe racks, and wherever structural efficiency matters. Matches ASTM A572 Gr.50 in strength.
Normalised and impact tested at –50°C. Mandatory for Qatar offshore structural steel, jack-up structures, heavy-lift crane frames, and LNG plant cold-zone steelwork. Available in plates and wide-flange sections. Full EN 10204 3.1 MTC with Charpy impact test results on all Qatar orders.
460 MPa yield with thermomechanical controlled process (TMCP) rolling. Used where weight savings are critical — Qatar offshore topsides, long-span structures, North Field module lifting frames, and large crane booms. Higher cost per tonne but fewer tonnes per structure. Requires careful WPS qualification.
The standard US carbon structural steel grade (250 MPa yield, 400–550 MPa tensile). Required on US-specification Qatar EPC projects — ASME-code designed oil & gas facilities, petrochemical plants, and US government-funded infrastructure in Qatar. Full ASTM MTC available from Doha stock.
Quenched and tempered plates at 370–470 Brinell (AR400) or 470–540 BHN (AR500). Not a structural grade — used for Qatar wear liner plates, chutes, hoppers, dredger components, and any surface subject to severe abrasive wear. Requires low-hydrogen welding procedures and preheat for Qatar fabrication.
Every structural steel product from Valiol Trading is supplied with full mill certification to the applicable international standard — as required by Qatar EPC contractors, QatarEnergy, and Doha construction specifications.
Hot-rolled structural steel Parts 1–6. S275 through S690. The primary Qatar and European structural steel standard. Includes all impact test sub-grades (JR, J0, J2, K2, NL, ML).
Hot-formed hollow sections. Better tolerances and corner radii than cold-formed. S275J2H and S355J2H most common. Preferred for Qatar primary structural columns and trusses.
Cold-formed hollow sections from coil. Cost-effective for lighter gauges ≤12.5mm wall. S275J2H and S355J2H. Widely used in Qatar secondary structural applications.
Standard US carbon structural steel. Minimum yield 250 MPa. Required on US-specification Qatar EPC projects and ASME-code structural design.
High-strength low-alloy (HSLA) structural steel. Grade 50 (345 MPa yield) is the most common for Qatar US-spec EPC construction and oil & gas projects.
Optimised for W-shape wide-flange sections in AISC-designed Qatar structures. Yield 345 MPa, with Fy/Fu ≤0.85 limit for seismic performance.
Pressure vessel quality (PVQ) flat products. P355NL and P460NL for Qatar LPG tanks, pressure vessels, and offshore module steelwork.
BIS standard for hot-rolled structural steel (Grade E250–E650). Required on Indian-funded Qatar EPC projects and South Asian contractor procurement.
Valiol Trading offers processing and documentation services through our Qatar-based network — saving time and cost by delivering steel ready for direct use on your Qatar project site or fabrication shop.
Structural sections cut to exact Qatar project lengths — eliminating waste and Qatar site cutting costs. Plate profiling (plasma and flame cutting) to CAD drawings or DXF files for gusset plates, base plates, stiffeners, and complex profiles. Tolerances to EN ISO 9013. Standard sections and plates cut-to-length from Doha stock.
Sa 2.5 shot blast surface preparation and one- or two-coat primer application (zinc phosphate, zinc-rich, epoxy) through our Qatar-approved processing partners — fully inspection-certificated for direct project delivery to Qatar sites. Reduces paint re-work at Qatar fabrication shops.
Full EN 10204 Type 3.1 Mill Test Certificates with heat number, chemical composition, mechanical test results (yield, UTS, elongation, Charpy), and dimensional verification — all heat-traceable to the finished product. EN 10204 3.2 (third-party witnessed) available for Qatar EPC contractor requirements.
XRF-based PMI testing for high-strength, alloy, and special grades — confirming chemical composition before Qatar project delivery. Critical for S460/S690, AR400/500, and Corten grades where misidentification carries structural risk on Qatar oil & gas and construction projects.
Pre-shipment inspection by SGS, Bureau Veritas, Intertek, or client-nominated TPI. Mill visit attendance and source inspection coordination for Qatar EPC contractors. Full inspection release notes, dimensional reports, and coating inspection certificates provided for every Qatar order.
Steel sections bundle-tagged by grid-line reference, erection mark, or section type for Qatar project delivery — ready for direct-to-erection handling. Reduces Qatar site sorting delays, minimises double handling, and supports just-in-time delivery to Qatar construction and EPC sites.
Valiol Trading supplies certified structural steel to every major sector of Qatar's construction, energy, and industrial economy — with full MTC 3.1 documentation and same-week Doha delivery.
S355 J2/NL sections and plates for Qatar onshore and offshore process modules, equipment skids, pipe racks, and structural supports in QatarEnergy, Ras Laffan, and North Field project facilities.
S355 NL and S460 NL high-toughness sections for Qatar offshore jackets, FPSO topsides, offshore wind structures, and subsea manifold support frames. Full Lloyd's Register or DNV documentation available.
IPE, HEA/HEB, UC sections and RHS/SHS in S275/S355 for Qatar industrial buildings, warehouses, commercial frames, mezzanines, and Doha construction and infrastructure projects.
S355 J2/K2 and ASTM A572 structural plates and sections for Qatar road bridges, pedestrian bridges, flyovers, underpasses, and transportation infrastructure across the Qatar road network expansion programme.
Structural sections and plates for Qatar power plant boiler supports, ductwork, stack structures, cable tray supports, transformer plinths, and Ras Laffan power station steelwork.
Structural steel for Qatar desalination plant frames, water tank structures, pump station buildings, pipeline supports, and water treatment plant steelwork in KAHRAMAA and Qatar Water projects.
Plates, flats, rounds, and hollow sections for Qatar steel fabricators and structural contractors — supplied cut-to-length, shot blasted, and primed for direct-to-fabrication delivery across Qatar.
S355 NL/ML and P355 NL impact-tested plates and sections for Qatar North Field LNG train structural steelwork, cryogenic module frames, and cold-zone structural applications requiring –50°C Charpy values.
ABS/DNV Grade A/B/D ship plates, bulb flats, flat bars, and structural sections for Qatar vessel construction, marine structures, and offshore support vessel (OSV) fabrication and repair.
Key questions from Qatar procurement engineers and project managers sourcing structural steel for Qatar EPC, construction, and industrial projects.
Ask Our Team →S275 has a minimum yield strength of 275 MPa and is the standard, most economical structural steel grade — suitable for secondary steelwork, pipe supports, miscellaneous frames, and general fabrication across Qatar construction and industrial sites.
S355 has a minimum yield strength of 355 MPa — approximately 29% higher than S275. This higher strength allows engineers to specify lighter (smaller/thinner) sections for the same applied load, which typically results in a lower overall steel tonnage and total project cost for primary structural frames — even though S355 costs slightly more per tonne. S355 is the preferred grade for primary structural steel in Qatar oil & gas modules, EPC projects, and large industrial buildings. Both grades have comparable weldability with standard welding procedures applicable to both.
The sub-grade in EN 10025 indicates the Charpy V-notch impact test temperature — i.e. the temperature at which the steel is guaranteed to absorb at least 27 Joules without brittle fracture:
JR — impact tested at +20°C (room temperature). Suitable for Qatar's climate where temperatures stay above 5–10°C. Most economical and the default for Qatar non-critical structural work.
J0 — impact tested at 0°C.
J2 — impact tested at –20°C. Required for Qatar offshore and cold-zone structural applications.
NL / ML — normalised or thermomechanically rolled, impact tested at –50°C. Mandatory for Qatar offshore structures, crane frames, and LNG plant steelwork. For most Qatar onshore construction, JR or J0 is technically sufficient. For offshore Qatar, North Field LNG, and heavy-lift structures, J2 or NL is specified.
Yes. Valiol Trading stocks and supplies ASTM A36, A572 Grade 42/50/60/65, and ASTM A992 structural steel in plates, beams, angles, channels, and bars. ASTM grades are required on US-specification Qatar EPC projects — including ASME-code designed facilities, US government-funded Qatar infrastructure, and many international EPC contractor projects that default to American design codes. We supply full ASTM mill certifications with each Qatar order. Contact our Doha team with your ASTM grade, section, size, and quantity for a same-day quote.
Hot-formed hollow sections (EN 10210) are manufactured at high temperature above the recrystallisation temperature of steel. This relieves residual stresses and gives a more uniform microstructure — tighter dimensional tolerances, smaller corner radii (better for corner welds), and availability in higher-strength grades (S355, S420, S460). They are the preferred choice for Qatar primary structural columns, main frame members, and any application where weld quality at corners is critical for Qatar EPC structural compliance.
Cold-formed hollow sections (EN 10219) are formed at room temperature from flat-rolled coil. Typically more economical in thinner gauges (up to 12.5mm wall) and widely available for Qatar secondary structural use — pipe supports, handrails, secondary frames, and miscellaneous steelwork. Cold forming introduces residual stresses and corner radii are slightly larger. For most Qatar general construction and fabrication, EN 10219 cold-formed sections are adequate and offer better value.
Yes. Valiol Trading supplies cut-to-length structural sections and cut-to-size plates for Qatar steel fabricators, machine shops, and EPC contractors across Doha and Qatar project sites. We offer plasma and oxy-fuel flame cutting from stock plates to your exact dimensions — profiles, rectangles, or complex shapes from CAD/DXF files. Standard stock sizes are available in sections from 6m or 12m lengths. Cut-to-length eliminates Qatar site waste, reduces transport costs, and speeds up fabrication. Contact our Doha team with your cutting list for a prompt quote including delivery to your Qatar location.
Yes. Valiol Trading sources structural steel from Emirates Steel (Abu Dhabi), regional mills (Hadeed/Saudi Arabia, Turkish mills), and European mills (ArcelorMittal, SSAB) as well as Indian mills (SAIL, JSW, JSPL, Tata Steel). For Qatar projects with specific in-country value (ICV) or regional sourcing requirements, we can supply with documentation confirming GCC-origin mill production. Availability of specific grades from Emirates Steel or other regional mills varies by section size and grade — contact our Doha team with your enquiry for current mill availability and Qatar delivery lead times.
API 5L, ASTM A106, A312 — seamless & ERW. Qatar gas & oil pipeline stock. MTC 3.1.
View Pipes
ASME B16.9 BW, B16.11 forged, socket weld & MSS SP-97 olets. Doha stock.
View Fittings
ASME B16.5 / B16.47 / API 6A. Spiral wound gaskets, RTJ rings & bolting. Same-week Doha delivery.
View Flanges
Gate, ball, globe, check, butterfly. API 600 / API 6D. NACE MR0175. Same-week Doha delivery.
View Valves